Error Message
- Invalid partition table
- Error loading operating system
- Missing operating system
- Invalid boot disk
- Inaccessible boot device
- The Master Boot program at the beginning of the hard drive displays the following messages when it cannot find the active partition on the hard drive or the boot record on that partition
- Use Fdisk to examine the drive for errors.
- Check the hard drive manufacturer's Web site for other diagnostic software
===============================================
Error Message
- Missing operating system, error loading operating system
- The MBR is unable to locate or read the OS boot sector on the active partition
- Boot from a bootable floopy and examine the hard drive file system for corruption or run scandisk from the Windows Installer CD.
===============================================
Error Message
- Bad sector writing or reading to drive
- Sector marking on the disk may be fading
- Try running Scandisk first (from the Windows Installer CD if nesessary). If it fails, consider reformatting the disk.
===============================================
Error Message
- Configuration/CMOS error
- BIOS setup information does not agree with the actual hardware the computer found during boot.
- May be caused by a bad or weak battery or by changing hardware without changing setup.
- Check BIOS setup for errors. If it doesn't work, try replacing the CMOS battery.
===============================================
Error Message
- Hard drive not found
- The operating system cannot locate the hard drive or the controller card is not responding.
- Check the hard drive power and IDE cable if these are properly attached.
- Else, check if the hard disk is detected using the auto-detect feature of the BIOS Setup.
===============================================
Error Message
- Fixed disk error
- The PC cannot find the hard drive t hat BIOS setup told it to expect.
- Verify if hard drive exists in BIOS setup information.
- Check power supply power cables, and connections.
===============================================
Error Message
- Invalid drive specification
- The PC is unable to find a hard drive or a floppy drive the BIOS setup tells it to expect.
- Look for errors in BIOS setup or for a corrupted partition table on the hard drive.
===============================================
Error Message
- No boot device available
- The hard drive is not formatted or the format is corrupted.
- Boot from a bootable disk and examine your hard drive for corruption or run scandisk from the Windows Installer CD.
- Check if an active partition has been set on the hard drive.
===============================================
Error Message
- Non-system disk or disk error
- Bad or missing command.com
- No operating system found
- The disk in drive A is not bootable or cannot find the OS on the hard disk.
- Remove the disk in drive A and boot from the hard drive. If no disk is in drive A, command.com on drive C might have been erased or the path could not be found.
- Check the hard drive for corruption
===============================================
Error Message
- Not ready reading drive A: abort, Retry, Fail?
- The disk in drive A is missing, is not formatted, or is corrupted.
- Try another disk or remove the disk to boot from t he hard drive.
===============================================
Error Message
- Bad command or file not found
- The OS command that was just executed cannot be interpreted or the OS cannot find the program file specified in the command line.
- Check the spelling of the filename
===============================================
Error Message
- Write protect error writing drive A:
- The disk in drive A is protected
- Let the computer write to the disk by sliding the write-protect tab (locked when hole is open) on the 3 1/2-inch disk.
===============================================
Error Message
- Track 0 bad, disk not usable
- This usually occurs when you attempt to format a floppy disk using the wrong formate type.
- The disk may also be physically damaged and can no long be used.
- Check the disk type and compare it with the type specified in the formate command.
- Replace the disk.
===============================================
Error Message
- Device not found
- Errors in System.ini, Win.ini or the registry.
- Look for references to devices or attempts to load device drivers.
- Use Device Manager to delete/disable the device or edit System.ini or Win.ini.
- Check for possible OS corruption.
===============================================
Error Message
- Device/Service has failed to start
- A hardware device or driver necessary to run the device or critical software utility is causing problems.
- This type of protection is best handled using OS troubleshooting methods and tools.
===============================================
Error Message
- Error in Config.sys line xx
- A problem has occurred when loading a device driver or withe the syntax of a command line.
- Check the command line for errors.
- Verify that the driver files are in the right directory.
- Reinstall the driver files, if necessary.
===============================================
Error Message
- Insufficient Memory
- This errors happens during or after the boot under Windows when too many applications are open.
- This also occurs when the (virtual) memory manager does not release unused memory or the hard disk used for the virtual memory is low on free space.
- Close some applications.
- Also consider rebooting the system to clear items from the memory.
- Consider cleaning (free up space) the hard disk used by the virtual memory.
No comments:
Post a Comment